Free NSE7-SDW-7-2 Fortinet NSE7-SDW-7-2 Practice Test Question - Page 2

Question 4 (Topic 1)

Refer to the exhibit. The device exchanges routes using IBGP. Which two statements are correct about the IBGP configuration and routing information on the device? (Choose two.)

Select an option, then click Submit answer.

○ Each BGP route is three hops away from the destination.
○ ibgp-multipath is disabled.
○ You can run the get router info routing-table database command to display the additional paths.
○ additional-path is enabled.

Question 5 (Topic 1)

Refer to the exhibits. Exhibit A - Exhibit B - Exhibit A shows an SD-WAN event log and exhibit B shows the member status and the SD-WAN rule configuration. Based on the exhibits, which two statements are correct? (Choose two.)

Select an option, then click Submit answer.

○ FortiGate updated the outgoing interface list on the rule so it prefers port2.
○ Port2 has the highest member priority.
○ SD-WAN rule ID 1 is set to lowest cost (SLA) mode.
○ Port2 has a lower latency than port.

Reference / correct answer:

FortiGate updated the outgoing interface list on the rule so it prefers port2.

Most accepted answer: A. FortiGate updated the outgoing interface list on the rule so it prefers port2.

Community votes: A=6, B=2, D=4

Selected Answer: AD sequence number sequence number and latency upvoted 1 times

Selected Answer: AD A & D are correct. A - from the log we see "Sequence Number: 2, 1" B - priority is for routes, thus the claim is not true D - from the log we "Others / Metric: latency" upvoted 3 times

Selected Answer: AB Remember the Priority configuration (port1 = 1 and port 2 = 10) is irrelevant here -- it only applies to traffic matching the implicit rule, not to SD-WAN member selection. Member sequence number is generally in order of configuration, however, In this case, the sequence has been modified by latency comparison between ports 1 and 2 based on the Best Quality SD-WAN strategy in use here. Thus B is correct. D looks like it could be correct if they completed the last word. This is a bad question. upvoted 4 times 0x194 1 year, 7 months ago I think it is A and D: A Correct -> Log: “Sequence number 2,1”. B Not correct -> I assume this refers to “set priority-members 1 2”. Therefore Port1 has the better priority. C Not correct -> Best quality. D Correct -> Presumably this should mean Port1 at the end, which then corresponds to answer A. upvoted 1 times ...

I think it is A and D: A Correct -> Log: “Sequence number 2,1”. B Not correct -> I assume this refers to “set priority-members 1 2”. Therefore Port1 has the better priority. C Not correct -> Best quality. D Correct -> Presumably this should mean Port1 at the end, which then corresponds to answer A. upvoted 1 times

Selected Answer: AD A. From the log -> Sequence Number D. From the log -> Sequence Number and Metric upvoted 4 times

Question 6 (Topic 1)

Refer to the exhibit. The administrator used the SD-WAN overlay template to prepare an IPsec tunnels configuration for a hub-and-spoke SD-WAN topology. The exhibit shows the FortiManager installation preview for one FortiGate device. Based on the exhibit, which statement best describes the configuration applied to the FortiGate device?

Select an option, then click Submit answer.

○ It is a spoke device that establishes dynamic IPsec tunnels to the hub. It can send ADVPN shortcut requests.
○ It is a hub device. It can send ADVPN shortcut offers.
○ It is a hub device and will automatically discover the spoke devices that are part of the SD-WAN topology.
○ It is a spoke device that establishes dynamic IPsec tunnels to the hub. The local subnet range is 10.10.128.0/23.

Free NSE7-SDW-7-2 – Fortinet NSE7-SDW-7-2 Practice Test Question